Skip to content

Need Help? Call us Now!

332-255-3200

News

How to Determine Door Handing Before Ordering Commercial Hardware

by Park Avenue Locks 02 Nov 2026
How to Determine Door Handing Before Ordering Commercial Hardware

Door handing is the direction a door swings when viewed from a defined side of the opening. For commercial locks, the common designations are left hand (LH), right hand (RH), left hand reverse (LHR), and right hand reverse (RHR).

Getting this detail right helps you choose hardware with the correct orientation. Before ordering, identify the outside of the opening, locate the hinges, and check whether the door swings toward you or away from you. Then compare your findings with the specific manufacturer’s handing diagram.

Why door handing matters

A lock can have the right finish and function but still be wrong for the opening if its handing is incorrect. Handing affects which side is secured, how the levers are oriented, and how the latch works with the door’s swing.

This is particularly important when comparing commercial mortise locksets or replacing existing hardware. Do not assume a new lock uses the same ordering designation simply because it looks similar to the old one.

How to determine door handing

Use this three-step method for the common commercial lock-handing convention described by Allegion:

  1. Stand on the outside of the opening. For a typical keyed opening, this is the security or key side. “Outside” does not necessarily mean outdoors; it may be the corridor side of an interior room.
  2. Locate the hinges. Hinges on your left indicate a left-hand orientation. Hinges on your right indicate a right-hand orientation.
  3. Open the door. If it swings away from you, it is a standard-hand opening. If it swings toward you, it is a reverse-hand opening.

Keep the same viewing position throughout the check. Switching sides halfway through reverses what you see and is an easy way to order the wrong hand.

Understanding LH, RH, LHR, and RHR

When viewed from the outside or security side:

  • LH: The hinges are on the left and the door swings away from you.
  • RH: The hinges are on the right and the door swings away from you.
  • LHR: The hinges are on the left and the door swings toward you.
  • RHR: The hinges are on the right and the door swings toward you.

You may also encounter “reverse bevel” terminology. Match the wording and diagram in the hardware manufacturer’s documentation rather than relying on abbreviations alone.

Does “inswing” or “outswing” tell you enough?

No. Those terms describe swing direction relative to a space, but they do not identify the hinge side.

For example, saying a door opens into an office does not tell a supplier whether its hinges are on the left or right. A useful ordering note identifies the viewing side, hinge location, and swing direction together.

Instead of writing “office door, inswing,” write: “Viewed from the corridor/key side: hinges on the right, door swings away from the viewer.”

That description gives the supplier a clearer basis for checking the required handing.

Are all commercial locks handed?

Do not assume every lock must be ordered handed, or that every lock can be reversed during installation. Check the exact model’s ordering guide and installation instructions.

When reviewing cylindrical lever locks or mortise hardware, look for an explicit statement about handing and field reversibility. If the instructions describe a handing change, follow that model’s procedure rather than applying instructions from another series.

The same caution applies when ordering other hardware. A lock’s handing designation should not automatically be used as the ordering designation for a hinge, closer, or accessory. Check each product’s instructions.

What to record before ordering

Handing is one part of identifying replacement hardware. Create a short opening record before choosing a product:

  • Door location or opening number.
  • Outside/security side of the opening.
  • Hinge side, viewed from that position.
  • Whether the door swings toward or away from that position.
  • Existing hardware manufacturer and model, if identifiable.
  • Door thickness and existing preparation measurements required by the replacement manufacturer.
  • Required lock function and finish.
  • Photos of both door faces, the door edge, and the frame strike.

Keep handing separate from measurements. Knowing that an opening is RHR does not establish its door thickness, backset, or compatibility with a particular lock.

Common door-handing mistakes

One common mistake is using the handle position instead of the hinge position. In the method above, the hinges determine left or right.

Another is assuming “outside” always means the exterior of the building. For an interior office, the relevant reference side may be the corridor or key side.

A third is leaving out reverse swing. Two doors can have hinges on the same side but swing in opposite directions. Recording only “left hand” or “right hand” may omit information the supplier needs.

Finally, avoid assuming a replacement is field reversible. Confirm that capability for the exact model before placing an order.

Frequently asked questions

What is the difference between RH and RHR?

Under the convention described above, both have hinges on the right when viewed from the outside/security side. An RH door swings away from the viewer. An RHR door swings toward the viewer.

Can I determine handing from a photograph?

A photograph is more useful when you identify which side it shows and indicate the swing direction. Include both sides of the opening and a photo with the door partly open, rather than relying on a close-up of the handle.

Does door handing tell me which lock function to order?

No. Handing describes orientation and swing. Lock function describes how the hardware operates. Confirm both before selecting the replacement.

Should I use the same handing description for every hardware item?

Not without checking the manufacturer’s guide. Use your opening record as the starting point, then verify how each product is ordered.

Order with the opening, not just the old lock, in mind

Before ordering commercial door hardware, stand on the correct reference side, identify the hinges, and record the swing direction. Compare that information with the manufacturer’s diagram and confirm the replacement’s function and preparation requirements.

A few clear photos and a complete opening record are more useful than guessing from an old lever’s appearance.

Manufacturer references

Prev post
Next post

Thanks for subscribing!

This email has been registered!

Shop the look

Choose options

Edit option
Back In Stock Notification
this is just a warning
Login
Shopping cart
0 items